Drilling/mounting camera on pre-cast concrete finish?
 

I'm from the North and only have owned wood framed homes. My new house in Lake Denham is pre-cast, concrete finished home. I'm assuming the concrete/stucco finish is directly on the concrete? Is it okay to drill into the concrete to mount a Nest camera? Perhaps some of the trim is wood and I can mount it there instead?

Suggestions welcome. Thanks

Just helped a neighbor install some brackets on concrete walls. For the first time I used SDS bits and a suitable impact drill, wow huge difference. You can probably get by with standard concrete bits and a regular drill. Use plastic inserts and associated screws, I suggest getting stainless steel to avoid rusting.

And to your original question, yes, the stucco should be directly over the concrete, very similar to our concrete/block home. I would go with longer plastic inserts, so you have some grip in the concrete and not just the stucco.

Tapcon
 

Tapcon
Hex-Washer-Head Concrete Anchors

Get these at all Big Box or hardware stores... :clap2:

On block construction, they will have a lentil to support the weight of the roof on openings for doors and windows. Not sure if they have those for the pre-cast tilt wall construction, so you may have more than just concrete and stucco to drill through, depending on where you are drilling.....

You are correct, and that is exactly what I just drilled through, and the SDS bits were fantastic. These went through the stucco, concrete, and steel with no problem. I had tried this before with concrete and cobalt bits, and it took forever.

Google video

installing nest camera on stucco

Thanks for the tips. I've used tapcon before. In my google search this may be an option, installing under the eave rather than drilling the concrete.

https://www.youtube.com/watch?v=UjWkB0UZM1M

As usual, Villagetinker has the solution. I have an impact drill (hammer drill) if you want to borrow it, but we won’t be there until mid September. PM me if you want to borrow it then.

I appreciate the offer. I have the tools I need. I won't be there until October. I close September 12th. Just getting prepared. Since we won't be there full time I want to be able to see my lawn is being cared for and the house is secure, hence the cameras.

Camera mount
 

I mounted two wireless cameras, one under the eaves that captures driveway and front of the house and one to a Sylvester palm near the back entrance that captures back door and rear of house. Super easy and no issues in the two years they have been up. Replaced battery annually. I have block and stucco and preferred not to mount to that.

Camera under wave.
 

I have installed two cameras under eaves screwing into soffit. Worked great, easy and have had no issues for years since. Cameras typically very light weight load and easily screw into the soffit. At least an option to consider.

A 1/4” impact drill works much better than trying to drill in concrete with a regular drill (which doesn’t really work). However, I also have a DeWalt 1/2” hammer drill, 20v, and with the right bit, that zips through concrete block and is pretty fast on solid concrete. There was a time, though, when I needed to pass a garden hose through a solid 8” concrete wall. I think I used. 3/4” hammer drill, and I was through in about three minutes. These tools can be rented. You don’t use them very often.

I attached two of min to the down spouts. Works fine.

If outdoors I mounted ours under the eve, and the screws went into the bottom of roof rafters, also keeps the camera a bit more protected, and ran the power cord into the attic to an outlet up there.

just a different option as I didn't want it into the concrete at this point in time

Just get a good diamond tip concrete drill bit and concrete screws. No problem!

Might want to check on a gutter mount if this is a Nest Battery Camera.
Wasserstein Weatherproof Gutter Mount Compatible with Google Nest Cam (Battery) (White) - Flexible Mounting For Nest Cam

concrete
 

Moved from here to brick house Texas ya gotta get a hammer drill to deal with it

I've drilled 1/2" holes in concrete footings for my gazebo with nothing but a dewalt 20 volt. It wasn't easy or fun but it can be done. Might have burnt out the drill though. LOL. Seems like there are other options for mounting that may work for me.

I always wanted to own a hammer drill. Now, I don't need one. Bummer.