Anyone know how to get the LinkSys router to work with Comcast?
 

I already have the Linksys software on my laptop since I was using it with DSL in NY. When I got here, I tried configuring the Internet connection and picked auto DCHP in the first box. This is usually the type of connection which is usually used by cable companies. But cannot get an internet connection thru the router hooked up to the modem. Any ideas would be appreciated.

-Dave-

Unplug the router. After a few seconds, plug it back in. Press and hold the router reset switch on the back for a few seconds.

If that doesn't work, do the same procedure with the comcast modem.

Good luck!

I wish you good luck if you're able to get this to work. I tried helping friends set up a Linksys router (and they are among the best) with a Comcast modem and couldn't get it to work. Tried all the routes of disconnecting, resetting, you name it. Even Comcast couldn't give me a straight answer. Ultimately the friends switched over to DSL and have had no problem since. If you are able to get it to work with Comcast, please post it so others will know how. Thanks!

Call Comcast
 

Comcast support should be able to help you. You are paying for their help desk.

Yoda:):)

Belkin worked for us...
 

It wasn't easy, but I did get the Linksys router to work with Comcast
 

Suggestions:
1. I purchased a new cable to connect the modem to the router. I was having problems with the cable provided by Comcast.
2. Contact Comcast to advise them about the problems you are having and ask them to recycle the modem connection.
3. After the modem is fully operational, connect the router to the modem and wait for it to be fully initialized.
4. Try the internet connection from the laptop. It may take several tries before it makes the connection.
5. Here are some of my settings:
Basic Setup: Automatic DHCP
Basic Wireless Settings
Wireless Network mode: Mixed
Wireless channel: 11-2.462 GHz
Wireless SSID: Enable
Wireless Security
Security mode: WPA Personal
WPA Algorithm: TKIP
WPA shared key: create a key

I also got my linksys to work with comcast. However it was a challenge. Than I tried to use a second laptop and could not make that one work. Put the Belkin back and it worked fine on both. Have not givin up yet as the linksys is more secure. Will try again on my next trip down. So if anyone comes up with more pearls of wisdom, lots of people interested.

Successful linksys connection
 

After many tries, I went to my account on the Linksys website to their FAQ on how to hook up to a cable modem.

Setting up the router:

Step 1: select auto DCHP and save settings.
Step 2: Enable MAC Cloning and select "Clone My Router" and select save settings.

Step 3: Power cycle the cable modem, router and computer. Turn off the power and then apply power first to the modem, then the router, then the computer. This synchronizes the router with the modem.

Apparently most cable companies require MAC cloning and it does seem to work. Well, whatever, we're up and running on the internet. I don't think I'll be turning the router off anytime soon. . . . . . just in case. :bowdown:

-Dave-

Do you have a MAC or Windows computer, or was this just a required setting?

In this case MAC does NOT mean the computer manufacturer. It means Media Access Control and is part of setting up a router. I just didn't know that it applied to cable company modems. I have a Windows computer. If you paste the link below into your browser, it will take you to the Linksys web site and the answer that I found.

http://linksys.custhelp.com/cgi-bin/...p?p_faqid=3686


-Dave-

We have a linksys router working with comcast and we found the most efficient way to get it working was to call the comcast tech help line. they had it operating within minutes. We were with comcast in atlanta and came here with the router, thinking we could just plug it in and go. But found out we needed to call the tech line, they were very helpful.
:laugh:

I tried talking with the Comcast people but unfortunately they didn't want to discuss the linksys router. They told me to call Linksys. It's just a matter of who you connect with I guess.

-Dave-

HB, I am not sure if the Linksys is a wireless router or not but if it is first turn off the wireless and use a wire LAN connection to start. Get that to work first and then fo for the wireless. Let me know the model number of the unit and I will ask out guy at work that is killer on setting up home systems. I will see if he has had problems with the Comcast and Linksys set ups.

As much as I dont like Comcast, It works great with my LinkSys Wireless Router. No problems what so ever from the get go..