[Juliewaters]

Hello. We just moved into the villages and noticed this round plate on the floor. I attached a pic. Does anyone know what this is for?
Thanks
Julie

[Ragman]

Electrical outlet; there should be a wall switch (probably with a red dot) that controls it.

[jswirs]

Originally Posted by Juliewaters

Hello. We just moved into the villages and noticed this round plate on the floor. I attached a pic. Does anyone know what this is for?
Thanks
Julie

electrical outlet, or junction box? If that has a screw I would remove it to access whatever is inside.

[Juliewaters]

Thanks so much

[Tmarkwald]

I have the identical floor outlet as well.

[Jima64]

Floor outlet so you don't have to run an extension cord to have a lamp,near a piece of furniture.

[tophcfa]

Hope it’s on a GFI, a water spill on the floor would not be good.

[TommyT]

As was already stated, "Floor Electrical Outlet" but there is more to the story. One side of the outlet is always "hot" while the other side is controlled by a switch. In our Lantana, we had a switch by the back sliders and one by the front door.

[JoelJohnson]

Originally Posted by TommyT

As was already stated, "Floor Electrical Outlet" but there is more to the story. One side of the outlet is always "hot" while the other side is controlled by a switch. In our Lantana, we had a switch by the back sliders and one by the front door.

Not sure you said it right, the "hot" side should be controlled by the switch, otherwise a short would make the whole box hot.

[Kenswing]

Originally Posted by JoelJohnson

Not sure you said it right, the "hot" side should be controlled by the switch, otherwise a short would make the whole box hot.

Our house is currently under construction. Those floor outlets are indeed 1/2 switched. One side hot, one side switched. We actually had them place two floor outlets in our living room. We'll use the hot sides for our motorized recliners and the switched side for lamps.

[TommyT]

Originally Posted by JoelJohnson

Not sure you said it right, the "hot" side should be controlled by the switch, otherwise a short would make the whole box hot.

NOPE !!!! One can make the outlet hot only on one side by pulling the dual contacts from each side. This makes the outlet have two circuit feeds.

[thevillages2013]

The advice you have received already is good but just be careful when you take that plate off . Don’t assume there will be a correctly wired outlet under there. Proceed with caution

[davephan]

If the outlet doesn’t have a wall switch, or any other outlet, you can add a Luton Castra wireless outlet switch, and then you can easily add a wireless switch to the wall. You can also switch the lamps on and off with a remote control, or your cellphone.

I’m changing out about 20 switches in my home. Most of the switches are incandescent only dimmers. I’m changing them out with Lutron dimmers that are incandescent / fluorescent / LED dimmers, then changing out dozens of incandescent bulbs with LED bulbs. Those lights can switched from your cellphone or automated.

I also changed out four mechanical wall timers with Lutron switches that can be programmed with your cellphone to turn on and off outside lights at sunset and sunrise.

I also added motion detectors to the lights in closets, the laundry room, and bathrooms, and countdown timers to the bathroom fans. The motion detectors are built into the switches, or are separate wireless motion detectors that can be “paired” to the switches. Then the lights turn on and off automatically. The fans shut off automatically.

You can even program the lights to make it look like you are home from the outside of your home at night with the automation. There’s a lot of things you can do to improve your electrical system in an older home.

[GOLFER54]

I think it is a CCTV

[NoMo50]

If yours is a new home, your builder should have explained that to you during your walk-through. You may also find several switches in the house that have a red screw on the switch plate. The red screw indicates that switch controls an electrical outlet. Find the outlet in the same room with a red screw on its cover, and the switch will control half of that receptacle...generally the top one.